Guides · Updated 2026-11-06 · 9 min read

PLA vs PETG vs ABS vs ASA vs TPU: Which Filament Should You Use?

Choosing a filament is mostly a trade between ease of printing and the demands placed on the finished part. A decorative figurine, a bracket on a hot dashboard and a flexible phone case all call for different materials. This guide compares the five most common filaments and ends with a short method for choosing among them. The numbers are typical values; always check the spool label and the manufacturer's data sheet, because blends differ.

At a glance

MaterialNozzle (typical)Bed (typical)Density (g/cm³)DifficultyBest for
PLA190–220 °C20–60 °Cabout 1.24EasyDisplay models, prototypes, figurines
PETG220–250 °C70–85 °Cabout 1.27ModerateFunctional parts, containers, outdoor-ish use
ABS230–260 °C90–110 °Cabout 1.04HardHeat-resistant parts, post-processing
ASA240–260 °C90–110 °Cabout 1.07HardOutdoor parts that face sun
TPU210–235 °C30–60 °Cabout 1.2Moderate to hardFlexible parts, grips, seals

PLA: the default for a reason

PLA is made from plant starch, prints at low temperatures and barely warps, so it works on almost every printer, even without a heated bed or enclosure. It holds fine detail and sharp edges, which is why most miniatures and display models are printed in it. The weak points are heat and brittleness: PLA softens at roughly 55–60 °C, so a part left in a parked car can deform, and thin PLA parts snap rather than bend. For anything that is only meant to be looked at, start here.

PETG: tougher and more forgiving of stress

PETG sits between PLA and ABS. It bends before it breaks, resists moisture and many chemicals, and tolerates somewhat higher temperatures than PLA. It is a good choice for water bottles' accessories, brackets and outdoor planters. In exchange it strings more, sticks very strongly to smooth build plates (use a release agent on glass or PEI) and shows layer lines more as small blobs unless retraction is tuned. It also absorbs moisture, so wet PETG makes bubbles and rough surfaces.

ABS: strong and heat-resistant, but demanding

ABS survives higher temperatures than PETG and can be sanded and smoothed with acetone vapour for a glossy finish. It shrinks as it cools, so it warps and cracks between layers in draughts. Print it in an enclosure, with a heated bed, and ventilate the room because heated ABS releases fumes with a noticeable odour. Choose it when the part must tolerate heat and you can control the printing environment.

ASA: ABS for the outdoors

ASA prints much like ABS but is designed to resist ultraviolet light and weathering, so it does not yellow and crack as quickly in the sun. Use it for garden items, car parts and outdoor enclosures. The same precautions apply as for ABS: enclosure, heated bed, ventilation.

TPU: flexible and impact-absorbing

TPU is a rubber-like filament used for phone cases, grips, gaskets and wheels. Print it slowly with reduced retraction; a direct-drive extruder makes this much easier than a long Bowden tube, where soft filament can buckle. Expect a lower layer-line definition and longer print times.

Drying and storage

Most filaments absorb moisture from the air. Typical signs of wet filament are popping sounds, small bubbles, hairy strings and rough surfaces. Common drying guidance, which you should compare with the manufacturer's advice: PLA at about 45–50 °C for 4–6 hours, PETG at 60–65 °C, ABS and ASA at 70–80 °C, TPU at 50–55 °C. Store spools in a sealed box with desiccant, and dry them again if they have been open for weeks.

How to choose in four questions

  1. Will it get hot? If it may exceed about 55 °C, skip PLA.
  2. Will it be outdoors in sun? Choose ASA, or PETG if the load is low.
  3. Does it need to flex or absorb shock? Choose TPU or PETG.
  4. Is it just for show? PLA gives the cleanest result with the least trouble.

Materials and your preview videos

When you present a print online, show the real material. Matte PLA and glossy PETG reflect light differently; the converter's material settings let you set colour and roughness so the preview resembles the filament you actually used. See Lighting and Materials for 3D Model Renders.

Weight and cost

Because densities differ, the same model weighs less in ABS than in PLA. Use the density column above together with the volume shown in the converter to estimate the weight; the method is described in Estimate 3D Print Weight and Filament Cost.

Frequently asked questions

Can I mix materials on one printer?

Yes, but purge the nozzle thoroughly and change temperatures. Switching from ABS to PLA without purging leaves charred residue that causes clogs.

Which filament is safest for beginners?

PLA. It tolerates imperfect settings and prints at low temperatures.

Is PETG food safe?

The raw material can be food-grade, but a 3D-printed part has tiny gaps where bacteria can grow, and additives vary. Do not assume a printed part is food safe.

Try it yourself: convert your own model to an MP4 video and preview images for free in your browser at STLtoMP4.com. Your files never leave your device.

Related guides

Browse all guides