Common 3D Print Problems and How to Fix Them
Most failed prints come from a short list of causes. This guide groups the common ones by symptom so that you can change one thing at a time and see what helps. It describes FDM printers that melt plastic filament; resin printing has different problems.
The first layer does not stick
Likely causes: bed not level, nozzle too far from the bed, dirty build surface, bed too cold. Try: re-level or run the printer's automatic levelling, clean the plate with isopropyl alcohol, lower the first-layer height slightly and use the bed temperature recommended for the filament. Print the first layer slower.
Corners lift (warping)
Plastic shrinks as it cools. Materials such as ABS and ASA shrink more than PLA. Try: a brim, a heated bed, no draughts, an enclosure for high-shrink materials, and rounded corners in the design.
Thin strings between parts (stringing)
Molten plastic oozes during travel moves. Try: dry the filament, lower the nozzle temperature by 5 to 10 degrees, enable retraction and tune its distance and speed, and increase travel speed.
Gaps, thin walls or rough surfaces (under-extrusion)
The printer is not delivering enough plastic. Try: check for a partial clog, make sure the filament path is free, verify the flow rate and raise the temperature a little. Damp filament also causes it.
Layers shifted sideways
Usually a mechanical issue: loose belts, a collision with a curled print, too fast acceleration, or a loose pulley. Try: check belt tension, lower speed and acceleration, and use a lower travel height or Z-hop where parts curl.
Drooping overhangs
Plastic has nothing to rest on. Try: rotate the model, add supports, increase part cooling, or print slower on the overhanging layers. See Best 3D Print Orientation.
Parts crack along layer lines
Weak layer bonding. Try: print hotter, reduce cooling fan speed for functional parts, and orient the part so the load does not pull layers apart. Add wall loops rather than only infill.
Blobs and zits
These appear where each layer starts and ends. Try: set the seam position to the back or a hidden corner and tune retraction.
A simple way to debug
- Change one setting at a time.
- Print a small test shape instead of a long model.
- Keep filament dry; store it in a sealed box with desiccant.
- Write down what worked for each material.
Frequently asked questions
How do I know whether the model or the printer is at fault?
Slice and print a known good calibration model. If it prints well, inspect the file for holes and thin walls, as described in How to Check an STL File Before You Print.
Quick diagnosis table
| Symptom | First thing to check | Second thing |
|---|---|---|
| First layer peels | Clean the plate | Nozzle height |
| Strings and hair | Dry filament | Retraction |
| Holes in top surface | More top layers | Infill density |
| Ringing (waves behind corners) | Lower acceleration | Tighten belts |
| Elephant foot (bulge at base) | Bed temperature slightly lower | Elephant foot compensation |
| Clicking extruder | Partial clog | Temperature too low or speed too high |
| Layer separation | Print hotter | Reduce fan |
Maintenance routine that prevents most failures
- Before each print: clean the plate, check the filament path and wipe the nozzle.
- Weekly: check belt tension, tighten loose screws and clean dust from fans.
- Monthly: lubricate rods or lead screws as the manual advises and inspect the nozzle.
- As needed: replace worn nozzles and build surfaces.
Material-specific tips
PLA fails mostly from first-layer and cooling issues. PETG fails from stringing and over-adhesion. ABS and ASA fail from warping and drafts. TPU fails from fast speeds. Knowing the typical weak point of each material tells you where to look first. See PLA vs PETG vs ABS vs ASA vs TPU.
When to stop a print
Stop a print early if the first layer is not sticking, if spaghetti forms in the air or if the nozzle collides with a lifted part. Continuing wastes filament and risks damaging the hot end.